Nowadays, as a means of transportation, cars have become more and more popular. Therefore, those who drive should be more careful, especially those who are on the road. They must pay attention to the traffic rules, and they must not be on the road to become road killers. Let's take a look at the problems that should be paid attention to by old drivers when they drive.

1. When we need to step on the brakes, it is best to glance at the central rearview mirror. The reason for this is to prevent the car behind from getting too close to us, and we suddenly step on the brakes to make the rear not respond, leading to a car accident.

2. Do not run side by side with the cart. Because the cart has a high chassis, the resulting blind spot is relatively large, so it is dangerous to go in parallel with the cart. Another point is that when traveling side by side with a large vehicle, the pressure of the gas will fluctuate quickly, which will cause the car to be “sucked” to the truck, which will easily lead to accidents.

3. When you want to go over the lane in the driving lane, be sure to hit the turn signal and give the rear vehicle a hint. If the rear vehicle also wants to cross the lane at this time, be sure to look at the headlights of the rear vehicles, because it can reveal to you whether you want to change lanes or if you change lanes first.

4. Although the rearview mirrors of the car are composite curved mirrors, there will still be blind spots. Therefore, when driving a car, you must pay attention to the central rearview mirror and observe the situation of the next rear vehicle. When we want to change the lane, there is also a number of hearts. Two-way integration can more effectively ensure our safety.

5, when driving, do not compete with other vehicles, even if you are very unhappy, but also peace of mind, must not be impulsive. Because the express train is based on danger, it is an act that is not responsible for self-safety.

6, in case of rainy days, in addition to slow down, but also have to pay attention to a little, that is, after a few kilometers of travel to gently click the brakes. The purpose is to scrape the water off the brake discs. This is to prevent the braking distance from increasing due to the presence of water on the brake discs in case of an emergency ahead.

The above is the driving skills of the old drivers. Traveling safely is a responsibility for the self. I hope the above suggestions can help more people.

Water-Cooled Industrial Chiller

New-designed RCM series of industrial chillers are capable of controlling precisely the mold temperature in plastic molding
process as so to shorten molding cycle and speed product formalization. The principle of heat exchange is adopted for cooling.
They can achieve rapid cooling, stable temperature controlling, and will be little effected by the surrounding factors. Therefore they
are necessary good equipments in modern industry.
1) Cooling temperature range 5-35°C.
2) High-capacity tube-in-shell evaporator with very good heat exchange performance especially under high ambient temperature condition.
3) Tube-in-shell condensers with excellent heat transfer and rapid cooling.
4) Stainless steel warm-keeping water tank.
5) R22 refrigerant to be used for efficient cooling.
6) R407 environment-friendly refrigerant is optional to use.
7) Overload protection for compressor, pump.
8) Independent Temperature Controller, anti-freeze protection.
9) Phase sequence protection for control circuit, refrigeration loop controlled by high and low pressure switch.
10) Warm-keeping design for all piping to avoid partial convection.
11) Suitable for machine cooling in industries of plastics, electroplating, foodstuff, electronic products

Introduction:
RCM-W series water cooled Industrial Chiller are applicable for cooling moulds to reduce products molding cycle, also they are available in the cooling of equipments in order to maintain a normal temperature. Besides, they are suitable for other industries
with the need of cooling.

Features:
Cooling temperature range 5~35°C.

Adopts stainless steel made insulated water tank and evaporator.

Equipped with anti-freeze thermostat.

R22 refrigerant is used as standard and optional R407 for efficient cooling.

Refrigeration loop controlled by high and low pressure switches.

Compressor and pump overload relays.

All adopt [COPELAND" US Brand compressors.

RCM-W series adopts tube-in-shell condenser design for quick heat transfer and excellent heat radiation.

Level meter of water tank is available as an option.

Low pressure pumps are standard configurations, while middle or high pressure pumps are optionally available.

Water-cooled industrial chiller schematic structure:

Screw Type Water-Cooled Industrial Chiller

Screw Type Water-Cooled Industrial Chiller,Industrial Chiller,Industrial Water Chiller,Screw Type Industrial Chiller

Ningbo Beilun Rhong Machinery Manufacturing Co., Ltd. , https://www.rhongmachinery.com