Keeping the car to see the patience summer car care

Timely maintenance and fine-tune life rhythm is accelerating, many people do not care about the car's maintenance, and even a bit like a routine, a look at the number of kilometers almost to run out of space to run 4S shop. Some models have been designed to be "comfortable," such as the Dongfeng Peugeot 207, which has intelligent maintenance tips, the so-called "smart", is reflected not only - just see the small wrench on the dashboard began to flash, then It shows that the car has to go to the “physical examination”; in addition, it is not a mechanical reminder, but the maintenance tips given by various indicators such as the number of cold start times and idle time of the integrated car, so as to better Extend the life of the vehicle. In addition, the 207 also achieved a long maintenance mileage interval of 15,000 kilometers, and on average it was about once or twice a year.

The original car can be so simple? In actual fact, although the vehicle was adjusted to the most humanized setting at the time of delivery, careful care will always return a one-point return.

As far as oil is concerned, under normal circumstances, the consumption of oil is not serious, and it is sufficient to use the cycle between two maintenances. However, in the summer, due to the hot weather, the oil consumption is higher than usual, and it is best to check once every two or three days. The method is very simple: first remove the oil gauge, clean it, insert it again, pull it out, and check the level of the oil level. If you find a loss of oil, you should make up for it in time. In addition, in daily inspections, such as the presence of oily impurities or petrol smells, and a light blue emission at the same time, it indicates that the engine has a problem and the parts may have been abnormally worn and should be repaired by the factory.

It is worth mentioning that the 15,000 km maintenance cycle of the 207 is relatively long compared to other models in the same class. For the 20,000 kilometers, the 207 only needs to be changed twice. At the same level as the POLO and Vios models, it needs to be changed at least three times. It is not difficult to see that the 207 not only saves time and care in terms of maintenance, but also saves the car owners a large amount of money for car maintenance. “It has won the hearts of the people.”

Pre-trip inspections are inescapable Many people will check out "mobile phones, wallets, and keys" while they are out. If you make good use of it, this small habit can help us effectively control the "too busy and forget about maintenance" possible negative impact on the car.

The first one is to check the tires. In summer, the road surface temperature is relatively high, and the environment for use of automobile tires has become even worse. Therefore, in addition to the one-week round inspection before daily driving, tire pressure should be regularly measured. One can effectively prevent the puncture.

In addition, if you find that too much tire loss may be tied, the best way is to replace the spare tire after the tire repair. Don't forget to replace the spare tire after use, to ensure that the four tires have the same tire pressure and wear. In general, the spare tires are relatively new, and the patterns on the tires are also relatively clear, which makes the four tires have different frictional forces, especially in the rainy season, which can potentially cause certain safety hazards.

Experts advise the owner to do his homework in advance and get acquainted with the location of the car spare tire and tools. For example, the spare tire of the Dongfeng Peugeot 207 sedan is placed in a more conventional place: the spare tire cover that pulls the suitcase can be seen.

Through the hook design, the cover can also be fixed in the open state, providing more convenient for the tire change. The spare tire of the 207 hatchback is suspended at the bottom of the vehicle for the storage space of the rat. Need to open the trunk first, lift the mat, use the small wrench to loosen the screw, turn the hook on the bottom of the car, the spare tire will be "dropped" and then drop, jacks placed in the middle of the line. At this time you will certainly lament the creativity of the French and will design each step so carefully.

Tips for maintenance In summer, some car maintenance suggestions related to temperature are very worth paying attention to. For example, the indoor air conditioner with the highest frequency of appearance is also very knowledgeable to use. There are many friends around the reporter who are accustomed to reaching the destination and then turn off the air conditioner. It is not known that after the vehicle is turned off, the operation of the ventilation fan will cause the condensed water to be difficult to discharge. The resulting mold contamination can cause odor. Therefore, it is advisable to turn off the air conditioner in a few minutes before reaching the destination, so that the temperature in the pipeline can be raised and kept dry, so that there is no need to worry about the problem of air conditioning odors.

For another example, after the rainy days, clean the vehicle with clean water in time to avoid surface residues of acid and damage the paint. Must not have the idea of ​​"under the rain = washed car"; can not use fresh water instead of antifreeze; do not let the car in a state of long-term exposure.

Toy Injection Molding Parts

Every service we provide has high praise from customers, life-long after-sales maintenance, rest assured shopping, packaged delivery, five-year warranty, damaged package, cooperation with many well-known brands at home and abroad, and a variety of varieties for you to choose. The mold opening time period is short, the workmanship is accurate and not sloppy, safe to use, not oxidized, and prolongs the service life.
We are an enterprise specializing in the production of Injection Molding Parts. The company integrates scientific research, design, production, sales and service. It has a full-steel experimental equipment production line, a plastic spray assembly line, a wooden school tool production line, etc., to provide our customers with high-quality products. The company has a full set of bidding documents, which can fully meet the bidding needs. The company's products have obtained a number of industry certifications, such as ISO9001 quality system certification, 18001 occupational health and safety standard certification, ISO14001 environmental management system certification, China Environmental Labeling Product Certification, China Environmental Protection Product Certification After-sales maintenance, rest assured shopping, packaged delivery, five-year warranty, damaged package, cooperation with many well-known domestic and foreign brands, a variety of varieties, you can choose. The mold opening time period is short, the workmanship is accurate and not sloppy, safe to use, not oxidized, and prolongs the service life.Img 9703 Jpg

Toy Injection Molding Parts,Plastic Injection Molding Parts,Abs Plastic Injection Molding Parts,High Precision Plastic Injection Moulding Parts

Suzhou Dongye Precision Molding Co.,Ltd. , https://www.sjinjectionmolding.com