Most of the electronic dashboards on the sprinkler are controlled by a computer and also have a self-test function. As long as the instructions are given to them, the electronic controller of the sprinkler's electronic instrument panel will perform the next inspection of the system corresponding to its main display device. As long as there is a fault in one of the systems, the controller will use different warnings to inform the driver that there is a fault in the display system, and it also shows the location of the sprinkler fault code storage . In order to facilitate the inspection and maintenance of the vehicle when the fault code from the inside out, rightly pointed out the location of the fault. When the sprinkler's electronic dashboard fails, it should be checked immediately.

A quick detector can be used to inspect the fault location. The quick detector can emit and simulate a variety of sensor models, and can quickly detect the location of the sprinkler fault. When using the tester to input signals to the instrument panel, if the display of the instrument panel is normal, then it proves that the circuit or the sensor has failed. If the display is not capable of display, then the tester is directly connected to the relevant input socket on the electronic instrument panel. If the display is normal at this time, it proves that the connector and the sprinkler harness have appeared. Problem, or else it proves that the dashboard has failed.

The computer quick tester can be used for detection. The computer quick tester is a signal that can simulate the flow of fuel and the speed of the vehicle. The alarm signal from the tester also needs to be input from different locations. The operation of the detection harness, the sensor number computer, and the display device is not normal.

Product Description
Grain cleaning machine Gravity Stone Remover
after raw material cleaning in grain  processing plants, to grading grain, concentrate to clean impurities, (such as blighted wheat, small corn cobs, etc.) and to remove sand, mud.  It use wind, vibrating and sieving effect matching technology, to be high efficiency, great performance on grading and separating gravel, mud pieces, low power consumption, no dust leakage, low noise, easy operation and maintenance.

Features
1. Advanced design and excellent fabricating
2. Reliable and excellent stone separation and efficient cleaning
3.High specific capacity
4. Easy operation and maintenance
5. Two options: with or without air-recycling system.
6.  A fan is equipped on the air-recycling type and a special separator is installed ahead of the fan. The separator deflects the aspirated air through a lamellar system so that dust and chaff are separated from the air and dischar
ged by an airlock valve while the cleaned air is recycled by the fan in the air return pipe to the destoner

Application
1.The machine is designed for separating stones from a continuous product stream
2.On the basis of differences in specific gravity, reliable removal of highdensity impurities such as stones and pieces of metal and glass is achieved.
3. Versatile application in flour mills, rice mills, feed mils and seeds selection processing.

Principle
1.The sieve box which is normally equipped with two layer sieves is supported by hollow rubber springs and is caused to oscillate by one or twovibrators depending on machine execution.
2.The grain is spread by a feeder across the entire width of the machine, and then the product stream is stratified on the pre separation screen according to its specific gravity by the oscillating motion of the screen and by the air flowing through the product from bottom to top. The light particles collect at the top, and the heavy ones including the stones at the bottom.
3.The lower layer with the heavy particles flows upward and is fed to the final separation zone of the bottom de-stoning screen. Final separation of the stones from the grain is accomplished by a countercurrent of air.
4. The stone free product streams on the two screens float on cushions of air, flowing slowly toward the product outlet, and then are discharged through the squeezed rubber valves.
5. To achieve the optimum degree of separation, the inclination of the screens, the air volume and final separation can be adjusted accordingly.
 
The process of flour milling:
The process of flour milling (from corn to milled into corn flour) usually consists of the following:
1. corn storage (silos, or warehouse)
2. cleaning system (sifter, destoner, seprater, magnet, scourer, etc)
3. dampening (dampener, conditioning silos, etc)
4. milling system (roller mill, plansifter, purifier, impact detacher, etc.)
5. Flour pressure and blending system (if need)
6. flour packing and stacking

DingZhou YongSheng Grain and Oil Machinery Co., LTD is a professional company combining research and development design, production and sales as a whole. The company has first-class oil equipment manufacturing base, professional oil technology engineer and professor, possesses advanced production technology and sophisticated equipment, All the mechanical parts are manufactured by our company.

The complete sets of oil equipment that we manufactured, relying on many domestic scientific research institutions. Advanced technology, suitable for making all kinds of plant oil. From the raw material of cleaning up, prepressing, leaching, refining and the production processing of by-product (such as Phospholipids engineering, protein engineering), is totally a dragon design and production, has created considerable economic benefit and social benefit for the user and society more than 40 years. Company new development of biodiesel equipment technology in recent years, has put dozens of sets on the market, obtaining good economical benefits both In the domestic and overseas. At present, we have hundreds of successful installation operation of the oil equipment engineering experience, can design and product according to the difference of the user's economic condition. raw material. regional, install oil equipments.

YongSheng comapny with scientific management method, strives for perfection the manufacturing process, innovative manufacturing idea, fast grows and become the grain and oil machinery production and export base in China. Company products are exported to Russia, India, Nepal, Indonesia, South Africa,Tanzania,Ethiopia,Ukraine, kazakhstan, Pakistan, Iran, north Korea, Vietnam, France and the European Union and so on more than 30 countries and area.

Stone Remover/Destoner

Grain Destoner,Grain Stone Removing Machine,Seed Cleaning Machine,Grain Destoner Gravity Machine

Dingzhou Yongsheng Grain & Oil Machinery Co.,Ltd. , https://www.oilpresschina.com